Flux is essential for creating clean solder joints with good penetration. Amtech flux is made in the USA.10cc syringe.

Used for checking LiPo, LiFe, Li-ion, NiMH and NiCd. battery packs.  Displays total pack voltage, individual cell voltage, lowest cell voltage, highest cell voltage, voltage gap between highest and lowest cells and remaining battery pack capacity (%).  Also functions as servo tester.

Specifications:

• Battery type/cells: LiPo/LiFe (1S-8 cells), NiCd/NiMH (1-8 cells)
• Displays: total pack voltage, individual cell voltage, lowest cell voltage, highest cell voltage, voltage gap between highest and lowest cells and remaining battery pack capacity (%).
• Also functions as sevo tester
• Size: 85x50x16mm
• Weight: 40g

EC3 style connectors are rated for high current draw (60A continuous), accept up to 12 gauge wire and are very easy to solder. Very ergonomic, easy to use and provide very little resistance. Designed so that the polarity cannot be reversed.  

EC5 style M on one end, T-Plug (Deans style) FM on the other.    

A handy, light-duty battery-powered soldering iron for soldering of small components.

• Convenient: Soldering kit for electronics is easy and convenient to operate, wireless design, small and lightweight, suitable for both home and field use, can be powered by computer, mobile power supply or your mobile phone charger etc..
• Adjustable temperature : Adjustable voltage/temp via knob, the adjustable range is 3.3V-4.8V.
• Fast Heating and Cooling: Copper alloy soldering iron heats up in less than 15 seconds, Cools down in less than 35 seconds.
• Application: For small-size circuits, home appliance accessories, welding, jewelry repair, DIY enthusiasts, etc., powered by batteries, suitable for indoor and outdoor use.
• Size: About 4*15*25cm,Package includes: 1pc x Soldering Iron 1pc x USB Cable 1pc x Bracket.

A powerhouse of a soldering iron, the Green 060 packs 60W of power in a handheld unit and even includes a dial to adjust temperature from 200-400C (392-842F).

It even comes with a high-grade ceramic heating element and an internal LED light which indicates when it is plugged in.  Uses standard 900 series tips that all Green soldering irons and stations use.

Green 907 solder handle is a direct replacement for 937 solder stations.  Ceramic heating element for superior performance and long life.

The Green 936 Digital Soldering Station combines a 60W unit with heavy-duty soldering iron with ceramic heating element. It heats up quickly to the selected temperature within a wide 392-896°F range, and holds that setting within 1.8°F while idle.

Features:

• Heavy-duty 60W design
• Heats up quickly to selected temperature, and holds settings within 1.8°F (1°C)
• Slender, insulated handle for comfortable grip
• Comes with iron stand and sponge

Specifications:

• Temperature: 200-480C (392-896F)
• Power Input: 110 to 240V
• Power Consumption: 60W
• Heating Element: Ceramic
• Cable Length: Soldering Iron Cable: 107cm (42"), AC Power Cable: 160cm (66")
• Dimensions: 12x9.3x7cm (4.7x3.7x2.8")
• Weight: 1.3kg (2.9lb)
• Includes: Solder station with handle, stand with sponge and fine-point tip

The Green 937 Digital Soldering Station comes with a digital temperature control unit and a heavy-duty soldering iron with a ceramic heating element.  The digital control provides precise heat control from 200 to 400C and features an easy-to-read LED display.  Simple push-button controls allow you to adjust heat in 1 degree increments and the security key locks in the selected temperature, preventing accidental changes.  

Features:

• Digital LED displays the selected temperature, heating status, and operational alerts
• Simple push-button controls adjust heat in 1° increments
• Security key locks the selected temperature, preventing accidental changes
• Temperature control unit holds the selected temperature within 1 degree when idle

Specifications:

• Temperature: 200-480C (392-896F)
• Power Input: 110V
• Power Consumption: 60W
• Heating Element: Ceramic
• Cable Length: Soldering Iron Cable: 107cm (42"), AC Power Cable: 160cm (66")
• Dimensions: 12x9.3x7cm (4.7x3.7x2.8")
• Weight: 1.3kg (2.9lb)
• Includes: Solder station with handle, stand with sponge and fine-point tip

A simple to use tool that easily plugs into the balance lead of your LiPo battery and automatically displays total pack voltage and individual cell voltages. Adjustable alarm can be set to trigger when cell votage reaches pre-set limit.

Specifications:

• Use for 1-8S Lipo/Li-ion/LiMn/Li-Fe
• Voltage detection precision: +_0.01V
• Unit voltage display range: 0.5-4.5V
• Total voltage display range: 0.5-36V
• 1S test mode voltage range: 4-15V
• Low voltage alarm mode for 2-8S
• Alarm set value range:OFF-2.7-3.8V
• Size: 40mm x 25mm x 11mm
• Weight: 9g
• Includes: Voltage meter and instructions

HobbyStar LiPo packs combine quality components and powerful cells to deliver a superior-power battery for your RC vehicle. Built using the latest technology in cell chemistry to provide generous capacities, powerful discharge ratings and fast charge rates.  HobbyStar LiPo batteries are an unbeatable value!

Specifications:

• Capacity: 10,000mAh
• Voltage: 7.4V (2S)
• Discharge Rating: 90C 
• Charge Rate: 2C
• Plug: HobbyStar Multi-Plug
• Balance Plug: JST-XH
• Dimensions: 154x27x45mm
• Weight: 430g  

Traxxas®, TRX® and ID® are registered trademarks of Traxxas L.P. The Traxxas®-style connector is not a Traxxas® product, it is only compatible with Traxxas® connectors.
Deans® is a registered trademarks of W.S. Deans Co. The Deans®-style connector is not a W.S. Deans Co. product, it is only compatible with Deans® connectors.
EC3™ and EC5™ are registered trademarks of Horizon Hobby, LLC. The EC3™ and EC5™ connectors are not Horizon Hobby, LLC products, they are only compatible with EC3™ and EC5™ connectors.

HobbyStar drag race packs utilize 4-6 parallel cells and a blistering 200C discharge rating to provide relentless levels of power previously unseen in 2S packs.  Larger packs are ideal for adding strategic weight, yet still feature the legendary HobbyStar cell-lightness for the given capacities. 

Specifications:

• Capacity: 10,000mAh
• Construction: 2S4P
• Voltage: 7.6V (2S HV)
• Discharge Rating: 200C 
• Charge Rate: 2C
• Plug: XT90
• Balance Plug: JST-XH
• Dimensions: 93x44x44mm
• Weight: 390g 

HobbyStar aircraft ESC's are top-of the line, full-featured ESC's at a competitive price.  High-voltage versions support 6S-12S input to reliably power your large-scale plane.  Constructed using only the highest-quality components and are encased in a beautifully machined heatsink housing to help keep operating temperatures in check.  Opto version ESC's allow you to run a separate, external BEC or a separate receiver battery in demanding applications. Integrated anti-spark circuitry eliminates sparking when connecting battery to ESC.  Includes mounting bracket for clean, sturdy installation that still permits ESC to be removed if necessary.

Features:

• Data logging system such as temperature, voltage, current, and RPM
• Extremely low internal resistance
• Advanced Governor Mode and soft start
• Power arm protection, over-heat protection, low-voltage protection and lost-signal protection
• Secondary sub-menu setting by the LCD program card or your PC
• Super smooth and accurate throttle linearity
• Support for most motors, including high RPM motors
• Programmable motor timing
• Anti-spark circuitry eliminates spark at battery connection
• Utilizes new smaller MOSFET technology to minimize weight
• Aluminum finned heat sink
• Programmable throttle input range

Specifications:

• Current: 120A Continuous, 150A burst (10s)
• Input: 18-38NiCd/6-12S LiPo
• OPTO, no BEC (external BEC or RX battery required)
• Dimensions: 65x46x17mm
• Weight: 120g

HobbyStar external BECs are specifically designed for demanding applications and therefore have the capability to support the higher momentary peak demand loads to eliminate the possibility of unwanted shutdowns. Simple to install and easily adjustable via push-button and LED indicators, HobbyStar BEC's provide peace of mind.

• Regulator Type: Switching
• Output: 5.0V, 5.5V, 6.0V, 6.5V, 7.0V, 8.0V (Output voltage is changeable by pressing a button)
• Input: 7V-60V (2-14S Lipo, 6-50 NiMH/NiCd)
• Output Current: Continuous Current 12A, Burst Current 18A for 10 seconds
• Size: 60mm x 34mm x15mm (LxWxH)
• Weight: 51g