T-Plug/Deans style M on one end, EC3 style FM on the other.

This is a connector for connecting two batteries with Deans style plug connectors in parallel. With two batteries connected in parallel you will have double the run time of a single battery, but with the same power as one battery. 14AWG wire.  

This is a connector for connecting two batteries with Deans style plug connectors in parallel. With two batteries connected in parallel you will have double the run time of a single battery, but with the same power as one battery.  

A high-quality HobbyStar connector for connecting two batteries with Deans style connectors in series. With two batteries connected in series you will have double the voltage and power of a single battery, but with the same run time as one battery. 14AWG wire.  

This is a connector for connecting three batteries with Deans style connectors in series. With three batteries connected in series you will have three times the voltage and power of a single battery, but with the same run time as one battery.  

Note: Make sure your motor/ESC are rated to handle the voltage supplied.

Set of one Female Tamiya to Female Deans, and one Tamiya Male to Male Deans connector. Used for adapting one style plug to the other. 14AWG wire, 15mm.  

HobbyStar driver sets are crafted with lightweight aluminum handles that feature a knurled surface that provides excellent grip on the tool during use.  An aluminum plug on the end further protects your hands during use and is also removable, allowing you to use the handle for storage of small items. Each driver has the size etched into the handle for easy identification, as well as unique lines on the top of each handle for quick ID in any position. The precision-cut, hardened tips fit fasteners snugly to avoid stripping out and are coated with a titanium nitrate that not only looks great but protects the tips from wear and corrosion.

• Metric Hex Driver Sizes: 1.5mm  2mm  2.5mm 3mm
• Ball End Metric Hex Driver Sizes:  1.5mm  2mm  2.5mm  3mm
• SAE Hex Driver Sizes:  0.05"  1/16"  5/64" 3/32"
• Metric Nut Driver Sizes:  4mm  5.5mm  7mm  8mm
• SAE Nut Driver Sizes:  3/16"  1/4"(x2)  11/32"
• Screwdriver Sizes:  3mm Flat  3mm Phillips  5mm Flat  5mm Phillips

HobbyStar titanium M3 screws combine light weight with incredible strength for the ultimate in hardware.

Pack of 10 screws.

Small RC cars deserve better than electronics that act brave for three laps and then start reconsidering their life choices. The HobbyStar TS80A is a compact 80A sensored brushless ESC built for 380/390 motor setups, giving 1/14 and small-scale race cars the smooth throttle control and tuning range they need without stuffing a giant 1/8-scale brick into the chassis.

It runs on 2S LiPo power with an 80A continuous and 160A peak current rating, plus a built-in 3A/6V BEC for clean receiver and servo power. The aluminum case, machined heatsink, and high-speed cooling fan help keep temperatures under control, which is useful when the car is small, the gearing is optimistic, and the driver has opinions.

The TS80A supports sensored 380/390/540 brushless motors, with motor limits of 10.5T and higher turn-count for 380/390 motors and 13.5T and higher turn-count for 540 motors. It includes an XT60 battery connector installed, factory preset Forward/Brake operation, programmable reverse, boost/turbo timing, blinky mode, and setup through an optional LED program card.

All the features of a race ESC in a smaller size for small-scale cars using 380/390 motors. 

Features:

• Efficient heat dissipating system
• High performance cooling fan (23,000RPM @7.2v)
• Aluminum casing with machined heatsink
• Built-in Super BEC
• Programable with optional LED Program Card
• Turbo/Boost timing and blinky modes

* Comes with XT60 Battery Connector Installed

Specifications: 

• Forward/Brake/Reverse: Yes (Factory preset at Forward/Brake)
• Dimensions: 29.50L x 29.52W x 24H mm (with Fan)
• Weight: 62g (with wires)
• Voltage Input: 6v-11v (2s LiPo)
• Peak Current: 160A
• Continuous Current: 80A
• Motor Limit: Over 13.5t (540), Over 10.5t (380/390)
• Motor Type: Sensored 380/390/540 Brushless Motor
• BEC: 3A/6V
• Multi Protection System: Yes

HobbyStar Turbo-Ventilator fans move a tremendous amount of air to aid in cooling high-power systems.  Durable machined-billet housing not only looks great but ensures reliable operation.

Specifications:

• Operating Voltage: 5.0V to 8.5V
• Size: 25mm x25mm x 10mm
• Mounting holes: 28mm apart (measured diagonally, hole-center to hole-center)
• RPM @ 8.5V: 32,000
• Current at 8.8V: < 0.5A
• Plug: JST 2-pin 

NOTE: Does not come with mounting screws.

HobbyStar Turbo-Ventilator fans move a tremendous amount of air to aid in cooling high-power systems.  Durable machined-billet housing not only looks great but ensures reliable operation.

Specifications:

• Operating Voltage: 5.0V to 8.4V
• Size: 30mm x30mm x 10.5mm
• Mounting holes: 34mm apart (measured diagonally, hole-center to hole-center)
• RPM @ 8.4V: 22,000 - 24,000
• Current at 8.4V: < 0.5A
• Plug: BEC style 2-pin (fits all standard receivers)

NOTE: Does not come with mounting screws.

HobbyStar Turbo-Ventilator fans move a tremendous amount of air to aid in cooling high-power systems.  Durable machined-billet housing not only looks great but ensures reliable operation.

Specifications:

• Operating Voltage: 5.0V to 8.5V
• Size: 35mm x35mm x 10mm
• Mounting holes: 40mm apart (measured diagonally, hole-center to hole-center)
• RPM @ 8.5V: 20,000
• Current at 8.8V: < 0.5A
• Plug: BEC style 2-pin (fits all standard receivers)

NOTE: Does not come with mounting screws.

HobbyStar Turbo-Ventilator fans move a tremendous amount of air to aid in cooling high-power systems.  Durable machined-billet housing not only looks great but ensures reliable operation.

Specifications:

• Operating Voltage: 5.0V to 8.5V
• Size: 40mm x40mm x 10.5mm
• Mounting holes: 45mm apart (measured diagonally, hole-center to hole-center)
• RPM @ 8.5V: 16,000
• Current at 8.5V: < 0.5A
• Plug: BEC style 2-pin (fits all standard receivers)

NOTE: Does not come with mounting screws.

HobbyStar Turbo-Ventilator fans move a tremendous amount of air to aid in cooling high-power systems.  Durable machined-billet housing not only looks great but ensures reliable operation.

Specifications:

• Operating Voltage: 5.0V to 8.5V
• Size: 50mm x50mm x 15mm
• Mounting holes: 56mm apart (measured diagonally, hole-center to hole-center)
• RPM @ 8.5V: 10,000
• Current at 8.8V: < 0.5A
• Plug: BEC style 2-pin (fits all standard receivers)

NOTE: Does not come with mounting screws.

HobbyStar Turbo-Ventilator fans move a tremendous amount of air to aid in cooling high-power systems.  Durable machined-billet housing not only looks great but ensures reliable operation.  Direct-fit for HobbyStar 1/10 Competition-Series ESC's.

Specifications:

• Operating Voltage: 5.0V to 8.4V
• Size: 30mm x30mm x 10.5mm
• Mounting holes: 34mm apart (measured diagonally, hole-center to hole-center)
• RPM @ 8.4V: 28,000
• Current at 8.4V: < 0.5A
• Plug: HobbyStar ESC (2-pin)

NOTE: Does not come with mounting screws.